Multifunction LCD Timer with backlight Programmable eight-function timer with seven time ranges from 0.001 sec to 9999 hours Key protect feature to prevent unauthorised timing mode change Display can be programmed to time UP or DOWN 100-240VAC or 24VAC/DC versions Backlit liquid crystal display of elapsed/remaining time and set time Two fully independent set times in recycling mode Long-life lithium battery for changing, displaying or storing the set time while power is off Universal contact or solid-state input terminals Signal inputs for start/gate and reset 48-DIN size with plug-in octal base Sockets available for panel, surface or DIN-rail mounting UL and CSA approved Ordering codes TDMS 3 Year Guarantee PRICE INFORMATION AND ORDERING T D M S 1 0 0-2 4 0 V A C TDMS 24VAC/DC Specifications Display Accuracy (timing modes) Setting error Repeat accuracy Variation due to voltage change Variation due to temperature change Type Signal inputs Contact resistance allowable Residual voltage allowable Reset pulse width Reset time By turning off power By signal input or manual reset Mechanical life Electrical life Allowable operating voltage range Contact ratings Supply frequency for AC voltage Power consumption Operating temperature Storage temperature Humidity Insulation resistance Dielectric strength Vibration Shock Surge resistance Noise resistance Static electricity resistance Timing ranges Protection rating Weight 2 x 4 digit LCD with backlight 0.01%20ms in total or less (for a signal start) 0.01%50ms in total or less (for a power supply start) Volt-free input 1kmax for contact closed, 100k min. for contact open 2V max for input ON 1ms on 9.999 sec range, 20ms on all other ranges 0.5 sec or less 20ms or less 50 million operations (18000 ops/hour) 100,000 operations at 5A 250V AC/30V DC resistive load (1800 ops/hour) 0.85 to 1.1 times input voltage range SPCO 5A at 250V AC/30V DC resistive load 50/60Hz Approx 1.5VA at 240V AC 50Hz, 0.8W at 24V DC -10 to +55C (avoid ice on timer) -25 to +65C (avoid ice on timer) 35-85% r.h. (non-condensing) 100M or more at 500V DC megger 2000VAC rms 1min between current carrying parts and non current carrying parts Mechanical/malfunction durability: 10-55Hz, 0.75mm double amplitude Mechanical durability: 500m/s2 (approx. 50G) Malfunction durability: 100m/s2 (approx. 10G) 4500V (500V for 24V AC/DC model) 1.2x50s applied twice according to JEC212 2000V by noise simulator Insx1s noise wave, 0 to 360 phase, 1 min, applied twice Mechanical durability: 15kV, malfunction durability: 8kV 0.001 to 9.999 secs 1 sec to 99 min 59 secs 0.01 to 99.99 secs 1 min to 99 hrs 59 mins 0.1 sec to 999.9 secs 1 hr to 9999 hrs 1 sec to 9999 secs IP54 120g approx. TDMS Programmable for eight timing functions see page 109 for timing chart Mode No. 1 On-delay Mode No. 5 Signal on-delay Mode No. 2 Signal off-delay Mode No. 6 On-delay (Power off pause) Mode No. 3 Interval (one-shot) Mode No. 7 On-delay integrating Mode No. 4 Symmetrical re-cycling Mode No. 8 Asymmetrical re-cycling Wiring diagrams Reset The TDMS has universal contact/solid-state inputs: 4 Contact Input Start/Gate Reset 5 3 6 2 7 1 Note: 1k max. for contact closed Note: 100k min. for contact open 4 Solid-state Input Start/Gate Reset 6 2 7 1 (+) 5 3 (+) 8 8 Power Power Note: Signal inputs approx. 6VDC open circuit and approx. 2mA when short-circuited When powering the 24VAC/DC mode using DC, the supply positive lead should be connected to terminal 7. Sockets Dimensions (mm) Surface/DIN rail mounting - screw terminal STD-8 Net weight approx 120g Flush mounting Flush mounting - screw terminal STF-8 Flush mounting - solder terminal ZSV8 PRICE INFORMATION AND ORDERING Panel cutouts For single units